ClockInfo.com

1) Early Golden Hour clocks (made around 1953 and 1954) don’t use nylon pads to support the rotating gear ring. Instead, they have three slightly raised metal areas. When these wear down, the friction increases and can cause the clock to be unreliable. On 3-31-08 I repaired one by applying several pieces of black plastic electrical tape near the raised metal areas. Time will tell how long this repair lasts.

2) The same job as above had a groove worn in the metal retaining ring, causing the the gear ring to bind in places. I used abrasive paper to remove the grove. Now the gear ring turns much more smoothly.

(Job 4583 3/31/08)

I overhauled the movement of this clock recently. One of the teeth on the escape wheel was too short, so I inserted a new tooth.

Both mainsprings are original Seth Thomas mainsprings that measure 0.0165 inch thick. The strike speed is adequate, but I wouldn’t want the mainspring to be much weaker. The pendulum takes a fantastic swing, about three times the escape arc. The time mainspring could be quite a bit weaker and still have plenty of power.

This clock appears similar to the College Series “New York” with a different base and glass. It is also very similar to one of the “Capitol” series with a different base and glass.

My job 4526.

When the Big Ben alarm clock was introduced in 1908, one of its important features was that the entire back of the case was the bell. This made the alarm ring louder and deeper than other alarm clocks of the time, which had a small bell on the top. When the Baby Ben alarm came out in 1910, it shared this feature of having the entire back as the bell. Until recently, all Big Bens and Baby Bens had this back bell.

Current production Baby Bens (made in China) have a small movement with a small internal bell. The back of the clock is PLASTIC, so obviously, it cannot be used as a bell!

Below is a slide show of a Baby Ben I purchased at Wal-Mart on March 8, 2008 for $7.97. It has a blue dial and back, and a silver color metal bezel and base. This shape of case is a reproduction of the style 8 Bens which were made from 1964 to 1981. The hands are luminous but the numerals are not. These new ones can be distinguished from the originals by having a plastic back and being made in China.

The movement has plastic gears for the center wheel through escape wheel, a plastic pallet assembly, and a plastic alarm escape wheel. The movement is labeled

NO(0) JEWELS
UNADJUSTED
SAILING.CHINA

The instruction sheet gives the following warranty:

Limited One-Year Warranty

Salton, Inc. warrants that this product will be free from defects in materials and workmanship for a period of one year from the date of original purchase. This warranty covers only the original purchaser of the product. Salton’s obligation to satisfy the warranty is limited to either of the following actions, at Salton’s option: repair the product or replace it. To receive the benefit of this warranty, you must send the product together with this warranty (marked with the retailer’s name and address and date of purchase) to:

Attn: Repair Center
Salton, Inc.
708 South Missouri Street
Macon, MO 63552
(800) 919-3101

Salton makes no other warranties, either express or implied except as set forth in this express warranty. To the extent that any Federal or state law creates an implied warranty for this product , the implied warranty is limited to one year from the date of original purchase. Salton is not liable for any incidental, direct or consequential damages or loss whether arising by contract or otherwise. Some states in the U.S.A. do not permit the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions my not apply to you. A consumer may have additional remedies granted by law. The warranty gives you specific legal rights and you may have other rights that vary from state to state.

Merritt’s Antiques has a new 3/4 inch by 0.0165 inch by 96 inch mainspring for American clocks. It is part no. P-1956, currently selling for $7.00 each individually (quantity discounts are available). It is a higher quality, American made version of their P-1496 that I have blogged about earlier.

I bought one of these springs to test. The quality appears to be excellent. The thickness measured as specified, 0.0165 inches. It is tempered to a nice uniform blue, and is well finished with a nicely made, neatly attached loop end.

It seems to have plenty of power, as the coils open way up when the spring is first uncoiled. It may be too strong for some clocks.

Tomorrow I am going to install it in an Ansonia long drop octagon clock with early type movement.